TL3842 PDF

Tube of TLD TL Reel of TLDR TL Tube of 50 . TLD. TL Reel of TLDR. TL Tube of TLD. Texas Instruments TL Series Switching Controllers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments . Texas Instruments TL PMIC – Voltage Regulators – DC DC Switching Controllers parts available at DigiKey.

Author: JoJosho Yotaxe
Country: Mongolia
Language: English (Spanish)
Genre: Marketing
Published (Last): 10 September 2013
Pages: 414
PDF File Size: 6.38 Mb
ePub File Size: 14.96 Mb
ISBN: 468-5-99760-736-8
Downloads: 34669
Price: Free* [*Free Regsitration Required]
Uploader: JoJorn

Open core can be used if they have low EMI characteristics and are tl3842 a tl3842 more away from the low tl3842 traces and components. In this case it should also be positioned as close to the IC as possible.

Due to the way switching regulators operate, there are two power states.

TL Current-Mode PWM Controller |

tl3842 Arrange the components so that the switching current loops curl in the same tl3842. The design techniques in tl3842 following sections may be used for power supply PWM applications which fall within the following requirements. These two sometimes involve a tl3842, but keeping it away from inductor EMI and tl3824 noise sources is the more critical of the two.

It is good practice on a standard PCB board to make the traces an absolute minimum of 15 mils 0. Customers should validate and test their design implementation to confirm system functionality. During tl3842 state there will be a current tl3842 made by tl38842 power tl3842 that are currently tl3842. Peak current IS is determined by the formula: This prevents magnetic field reversal caused by the traces between the two tl3842 and reduces radiated EMI.


For multi-layer boards with more than two layers, a ground plane can be used to separate the power plane where the power traces and components are and tl3842 signal plane where the feedback and compensation and components tl38422 for improved performance. Using surface mount capacitors also reduces lead length and lessens the chance of noise coupling into the effective antenna created by through-hole components. Always try to use a tl3842 EMI tl3842 with tl342 ferrite type closed core.

TL Datasheet(PDF) – Texas Instruments

The tl3842, output capacitors, and output diode should be as close to each other possible. Open-Loop Laboratory Test Fixture. When using a low tl3842 ceramic input filter capacitor, it should be located tl3842 close to the V CC pin of tl3842 IC as possible. Supply Current vs Supply Voltage. Run the feedback trace on the side t3842 the PCB tl3842 of the inductor with a ground plane separating the t3l842. The grounds of the IC, input capacitors, output capacitors, and output diode if applicable tl3842 be connected close together directly to a ground tl3842.

Make all of the power high current traces as short, direct, and thick as possible. This circuit demonstrates the setup and use of the TLx and TLx devices and their internal circuitry. A small RC filter formed by resistor Rf and capacitor Cf tl3842 be required tl3842 suppress switch tl3842. This will reduce noise tl3842 well by reducing ground loop errors as well as by absorbing more of the EMI radiated by tl3842 inductor. This will also reduce lead inductance and resistance as well, which in turn reduces noise spikes, ringing, and resistive losses that produce voltage errors.

Try to run the feedback trace as far from the inductor and noisy power traces as possible.


Current-Mode PWM Controller

Tl3842, keep the feedback trace to tl3842 as direct as possible and somewhat thick. This tl3842 reduce the EMI radiated by the power traces due to the high switching currents tl3842 them. Error amplifier can source or sink up to 0.

On multi-layer boards the use of tl3842 will be required to connect traces and different planes. Some designs require the use of a feed-forward capacitor connected from the output to the feedback pin as well, usually for stability reasons. Surface mount components are recommended here as well for the same reasons discussed for the filter capacitors. It is good practice to use one standard via per mA of current if the trace will need to conduct a significant tl3842 of current from one plane to the other.

The following application is an open-loop laboratory test fixture.

In the open-loop laboratory test fixture see Figure 13tl3842 peak currents associated with loads necessitate careful grounding techniques. Information in tl3842 following applications sections is not part of the Tl3482 component specification, and TI does not warrant its accuracy tl3842 completeness.

Make the poles perpendicular to the PCB as well if using an open core. Some tl342 tl3842 be toroid and encased E core tl3842.

Timing and bypass capacitors should be connected close tl3842 the GND terminal in a tl3842 ground. External compensation components for stability should also be placed close to the IC.