Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual (basic) is intended for users who “just want to run the inverter”. If you are going to utilize.

Author: Motaxe Gora
Country: Burundi
Language: English (Spanish)
Genre: Career
Published (Last): 5 April 2015
Pages: 214
PDF File Size: 11.19 Mb
ePub File Size: 14.81 Mb
ISBN: 923-1-56011-837-3
Downloads: 64423
Price: Free* [*Free Regsitration Required]
Uploader: Dushakar

Page Frequency setting by mitsubishu input terminal 2, 4 Parameter Perform operation by analog input current When the pressure or temperature is controlled constant by a fan, pump, etc. Operation selection at power failure Parameter Operation continuation at instantaneous power failure mitsubishi e700 inverter manual Pr.

Auto tuning is not performed under Advanced magnetic flux vector control or Perform offline auto tuning. Always keep the inverter clean.

Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller

Page The above parameters can be set when Pr. When the PU is discon- tion modes. Inverter may be damaged. Page Turn the digital dial to set the value to ” When using the SU signal, set “1 positive logic or negative logic ” in Pr.

PWM carrier frequency at stop-on contact Mitsubishi e700 inverter manual set in Pr.

Good heat dissipation is achieved through the vertical alignment of the frequency inverter, the side-by-side mounting and maintenance of minimum clearances. Adjust the output torque current of the motor Parameter Setting of mitsubishi e700 inverter manual prevention operation in high frequency range Pr.


By setting “0”, the output terminal turns off on for sink logic.

The number mitsubishi e700 inverter manual characters decreases by 1. To the alarm detection sensor IE Fig. This function uses the eddy current brake principle, stopping the motor by applying a pulsed DC voltage to the motor stator.

Page For write, set the data as a control input instruction.

Do not use these pins for RS communication. PU operation mode Basic settings 5. Function assignment of external terminals Parameter 6. Page Simple mode parameter list Basic settings Before performing offline auto tuning Check the following before performing offline auto tuning. Function assignment of external terminals Parameter Zero current detection Y13, Pr. Signal adjustment of mitsubishi e700 inverter manual 2 Initial value 50Hz Gain Pr.

Page 47 Refer to section 6. Page Motor brake and stop operation Parameter Operation voltage torque setting Pr. Page 32 Enclosure design Installation Cooling system types for inverter enclosure From the enclosure that contains the inverter, the heat of the inverter and other equipment transformers, lamps, resistors, etc. Any equipment mitsubishi e700 inverter manual above the inverter should be heat resistant.

Page When stall prevention operation is performed, the OL signal is output. Page Function assignment of external terminals Parameter When you refer to Fig.

One to two mitsubishi e700 inverter manual of periodic inspection cycle is recommended. LED of Hz flickers during stop and is lit during operation. Operation panel Operation Function Description Used to change the frequency setting mitsubishi e700 inverter manual parameter values. Page 8 Additional Instructions Also note the following points to prevent an accidental failure, injury, electric shock, etc. Frequency setting by external terminals Parameter Frequency setting by external terminals Refer to Purpose Parameters that must be set Mitsubishi e700 inverter manual Make frequency setting by combina- Multi-speed operation Pr.


NOTE Refer to section 5. OLT appears to trip the inverter output. Inverter reset Stall Prevention overcurrent Stall prevention overvoltage Regenerative brake prealarm Warnings Electronic thermal relay function prealarm Page 85 Check if there is no gap between the actual speed and commanded speed by comparing the inverter speed command and detected speed of the speed detector.

External operation Basic settings External operation From where is the frequency command given? The parameter number read previously appears. Check first when you have troubles Troubleshooting mitsubishi e700 inverter manual. Afterwards you mtisubishi then reset Pr. Mnual operation mode cannot be switched directly between the PU operation mode and network operation mode. Inspection Maintenance and inspection 8. When encasing multiple inverters, install them in parallel as a cooling measure.

Table of Contents Add to my manuals Add.


The AU signal need not be input. After the inverter has started up in the network operation mode, parameter write and operation can mitsubishi e700 inverter manual performed from a program.

In addition, negative logic can be set on when the inverter is normal, off when the fault oc- curs.